Skip to main content
Civil & Structural EngineeringPublished 2026-04-2014 min read

Terzaghi vs. Meyerhof Bearing Capacity: Shallow Foundation Design & Water Table Effects

A rigorous geotechnical engineering guide comparing Karl Terzaghi (1943) and George G. Meyerhof (1963) shallow foundation bearing capacity formulations. Analyzes failure wedge geometry, compares bearing capacity factors (Nc, Nq, Ngamma) and depth/shape modifiers, establishes exact groundwater table buoyancy corrections across Cases I, II, and III, and solves a 2.0 m x 2.0 m square footing benchmark under dry and submerged conditions.

Author: Md. Nur Islam•Founder of EngiVanta

Designing shallow foundations—whether isolated column footings, continuous strip wall footings, or mat slabs—requires geotechnical engineers to satisfy two independent design criteria: ultimate bearing capacity (prevention of shear failure within the supporting soil mass) and tolerable total and differential settlement. While settlement frequently governs in granular soils with large footings, ultimate bearing capacity provides the fundamental safety ceiling (q_ult) upon which design allowable bearing pressures (q_all) are established.

In classical soil mechanics, two foundational formulations dominate commercial geotechnical practice: Karl Terzaghi’s seminal 1943 formulation and George G. Meyerhof’s 1963 generalized bearing capacity equation. While Terzaghi simplified the failure mechanism by neglecting soil shear resistance above the foundation base level and assuming a semi-infinite surcharge, Meyerhof extended the slip surface up to the ground surface, introducing comprehensive shape, depth, and load inclination factors. Furthermore, fluctuating groundwater tables represent one of the most severe hazards in foundation engineering, capable of slashing the ultimate bearing capacity of cohesionless soils by more than 50% due to pore water buoyancy.

This technical guide provides a rigorous side-by-side comparison between Terzaghi and Meyerhof formulations, examines the geometric failure zones beneath footings, details exact groundwater table correction models (Cases I, II, and III), and works through a verified 2.0 m x 2.0 m isolated square footing benchmark cross-checked under both dry and submerged conditions.

1. Soil Failure Modes Beneath Shallow Foundations

When an axial compressive load is applied to a shallow foundation (embedment depth Df <= width B), the supporting soil shears through one of three distinct modes identified by Vesic (1973):

• General Shear Failure: Continuous slip surface extends from the footing base all the way to the ground surface, accompanied by substantial soil heave. Occurs in dense sand (relative density Dr > 70%) or stiff clay (cu > 100 kPa). This forms the basis of both Terzaghi and Meyerhof equations.

• Local Shear Failure: Slip surface terminates within the soil mass without breaching the ground surface; only slight bulging is observed. Occurs in medium sands (35% <= Dr <= 70%). Terzaghi recommended reducing strength parameters: c* = (2/3)c and tan(phi*) = (2/3)tan(phi).

• Punching Shear Failure: Footing sinks vertically like a piston without outward heave. Occurs in very loose sands (Dr < 35%) or soft clays.

2. Geometry of the Failure Surface

Under general shear failure, the soil beneath a rough strip footing is divided into three distinct zones:

1. Zone I (Active Elastic Wedge): Directly beneath the footing base. Concrete-soil friction prevents lateral expansion, forcing the wedge to move downward as an integral part of the footing.

2. Zone II (Radial Shear Zone): Logarithmic spiral zone where soil is in plastic equilibrium.

3. Zone III (Passive Rankine Zone): Linear slip lines inclined at 45° - phi/2 extending outward to the ground surface.

3. Karl Terzaghi’s (1943) Classical Formulation

Terzaghi formulated ultimate gross bearing capacity (q_ult) as the superposition of three physical contributions: cohesion (c), overburden surcharge (q = gamma * Df), and soil self-weight (0.5 * gamma * B * Ngamma):

CE Toolbox: Terzaghi Shallow Footing Bearing Capacity

ce-geo-01

Solve Terzaghi shallow foundation ultimate and allowable bearing capacity across strip, square, and circular footings.

Governing Formulation:
q_ult = c · N_c + q · N_q + 0.5 · γ · B · N_γ (Strip Footing)

Terzaghi Bearing Capacity Factors

Terzaghi expressed Nq and Nc analytically, while Ngamma was provided via numerical integration curves accurately parameterized by Kumbhojkar (1993):

• Nq = a² / [2 · cos²(45° + φ/2)], where a = exp[(3π/4 - φ/2) · tan(φ)]

• Nc = (Nq - 1) / tan(φ) [For φ = 0°, Nc = 5.70, Nq = 1.00]

• Ngamma = [2 · (Nq + 1) · tan(φ)] / [1 + 0.4 · sin(4φ)] (Kumbhojkar 1993)

Terzaghi Shape Modifications

• Square Footing (B x B): q_ult = 1.3 · c · N_c + q · N_q + 0.4 · γ · B · N_γ

• Circular Footing (Diameter B): q_ult = 1.3 · c · N_c + q · N_q + 0.3 · γ · B · N_γ

• Rectangular Footing (B x L): q_ult = c · N_c · (1 + 0.3 · B/L) + q · N_q + 0.5 · γ · B · N_γ · (1 - 0.2 · B/L)

4. George G. Meyerhof’s (1963) General Bearing Capacity Equation

Terzaghi assumed soil above the foundation depth acts purely as a surcharge, neglecting its shearing resistance. Meyerhof extended the slip surface to ground level, incorporating explicit modifiers for footing shape (s), embedment depth (d), and load inclination (i):

Governing Formulation:
q_ult = c · N_c · s_c · d_c · i_c + q · N_q · s_q · d_q · i_q + 0.5 · γ · B · N_γ · s_γ · d_γ · i_γ

Meyerhof Factors & Modifiers

• Nq = exp(π · tan(φ)) · tan²(45° + φ/2)

• Nc = (Nq - 1) · cot(φ) [For φ = 0°, Nc = 5.14, Nq = 1.00]

• Ngamma = (Nq - 1) · tan(1.4φ)

• For shallow footings (Df / B <= 1.0): sc = 1 + 0.2·Kp·(B/L); sq = sgamma = 1 + 0.1·Kp·(B/L) for φ >= 10° (where Kp = tan²(45° + φ/2)); dc = 1 + 0.2·sqrt(Kp)·(Df/B); dq = dgamma = 1 + 0.1·sqrt(Kp)·(Df/B).

5. Direct Side-by-Side Comparison: Terzaghi vs. Meyerhof

The fundamental differences between Terzaghi (1943) and Meyerhof (1963) reflect conservative classical assumptions versus generalized failure mechanics.

Table 1: Fundamental Comparison Matrix
Technical ParameterKarl Terzaghi (1943)George G. Meyerhof (1963)Practical Geotechnical Impact
Overburden Shear ResistanceNeglected (treated as uniform surcharge q)Included up to finished ground surfaceTerzaghi is more conservative; Meyerhof reflects true embedment gain
Embedment LimitStrictly shallow: Df <= BShallow and deep foundations (Df > B)Meyerhof handles deeper pier foundations seamlessly
Cohesion Factor at phi = 0Nc = 5.70Nc = 5.14 (Prandtl exact)Terzaghi yields higher capacity for undrained clay strip footings
Friction Factor Ngamma at 28°Kumbhojkar: 14.59Meyerhof formula: 11.19Terzaghi produces higher self-weight wedge capacities for sand
Depth Factors (d)None (d = 1.00 implicitly)Explicit depth modifiers (dc, dq, dgamma >= 1.0)Meyerhof rewards deeper embedment with 20% to 30% higher capacity
Load InclinationNot explicitly addressedFully integrated inclination factors (ic, iq, igamma)Meyerhof essential for retaining wall and wind/seismic base design
Commercial AdoptionStandard of practice for conservative spread footingsPreferred in structural-geotechnical softwareBoth widely accepted across international civil codes

6. Groundwater Table (GWT) Corrections: Cases I, II, and III

Groundwater exerts pore water pressure (u), reducing effective stress (sigma' = sigma - u). Submerged soil effective unit weight is gamma' = gamma_sat - gamma_w (where gamma_w = 9.81 kN/m³), roughly half of dry weight. The impact depends on water depth (dw) relative to embedment (Df) and width (B):

• Case I (0 <= dw <= Df): Water table within embedment depth. Surcharge is q = gamma * dw + gamma' * (Df - dw); wedge unit weight is gamma_wedge = gamma'.

• Case II (Df < dw <= Df + B): Water table within influence depth B below footing base. Surcharge is q = gamma * Df; average wedge unit weight is gamma_avg = gamma' + [(dw - Df)/B] * (gamma - gamma').

• Case III (dw > Df + B): Water table below influence depth. Zero reduction: q = gamma * Df and gamma_wedge = gamma.

7. Comprehensive Worked Benchmark: Isolated Square Footing

We evaluate an isolated column square footing (B = 2.0 m, L = 2.0 m, Df = 1.5 m) in silty sand (c = 15.0 kPa, phi = 28.0°, gamma = 18.0 kN/m³, gamma_sat = 20.0 kN/m³, gamma' = 10.19 kN/m³) with safety factor FS = 3.00.

Table 2: Benchmark Input Parameters
ParameterPlain-Text ValueEngineering UnitSource / Physical Basis
Footing TypeIsolated Square Pad-Concentric column spread foundation
Footing Width (B)2.0mFoundation transverse dimension
Footing Length (L)2.0mFoundation longitudinal dimension
Embedment Depth (Df)1.5mDepth from ground surface to base
Soil Cohesion (c)15.0kPaSilty sand shear strength test
Friction Angle (phi)28.0degreesTriaxial / direct shear failure envelope
Moist Unit Weight Above Base18.0kN/m3Soil bulk unit weight above base
Saturated Soil Unit Weight20.0kN/m3Saturated unit weight below water table
Unit Weight of Water (gamma_w)9.81kN/m3Pure water standard specific weight
Submerged Unit Weight (gamma')10.19kN/m320.00 - 9.81 kN/m3
Factor of Safety (FS)3.00DimensionlessStandard geotechnical safety margin

Bearing Capacity Factors at phi = 28.0 degrees

At phi = 28.0°: Terzaghi Nc = 31.61, Nq = 17.81, Ngamma = 14.59 (shape factors: sc = 1.30, sq = 1.00, sgamma = 0.80).

Meyerhof Nc = 25.80, Nq = 14.72, Ngamma = 11.19. Modifiers for B/L = 1.0 and Df/B = 0.75: sc = 1.554, sq = sgamma = 1.277, dc = 1.250, dq = dgamma = 1.125.

Table 3: Bearing Capacity Factors & Modifiers at phi = 28.0 degrees
Factor DescriptionTerzaghi (1943) ValueMeyerhof (1963) ValueFormula Basis
Cohesion Factor (Nc)31.6125.80Terzaghi analytical / Meyerhof (Nq-1)cot(phi)
Surcharge Factor (Nq)17.8114.72Terzaghi a^2/2cos^2 / Meyerhof e^(pi*tan)*tan^2
Soil Weight Factor (Ngamma)14.5911.19Kumbhojkar closed-form / Meyerhof (Nq-1)tan(1.4phi)
Shape Factor sc1.3001.554Terzaghi empirical / Meyerhof 1 + 0.2*Kp*(B/L)
Shape Factor sq1.0001.277Terzaghi baseline / Meyerhof 1 + 0.1*Kp*(B/L)
Shape Factor sgamma0.8001.277Terzaghi empirical / Meyerhof 1 + 0.1*Kp*(B/L)
Depth Factor dc1.000 (neglected)1.250Meyerhof 1 + 0.2*sqrt(Kp)*(Df/B)
Depth Factor dq1.000 (neglected)1.125Meyerhof 1 + 0.1*sqrt(Kp)*(Df/B)
Depth Factor dgamma1.000 (neglected)1.125Meyerhof 1 + 0.1*sqrt(Kp)*(Df/B)

Bearing Capacity Across Hydrological Conditions

Condition A (Dry Subgrade, dw >= 3.5 m): Terzaghi q_ult = 616.40 + 480.82 + 210.10 = 1,307.32 kPa; q_all = 435.77 kPa; allowable column load Q_all = 1,743.08 kN. Meyerhof q_ult = 751.65 + 570.66 + 289.04 = 1,611.35 kPa; q_all = 537.12 kPa; Q_all = 2,148.48 kN (+23.3% higher than Terzaghi due to depth factors).

Condition B (Water Table at Footing Base, dw = 1.5 m): Surcharge is unchanged (480.82 kPa). Wedge soil is submerged (gamma' = 10.19 kN/m³), reducing the Terzaghi third term from 210.10 kPa to 118.94 kPa (-43.4% reduction). Terzaghi q_ult = 1,216.16 kPa; q_all = 405.39 kPa; Q_all = 1,621.56 kN (loss of 121.52 kN column capacity).

Condition C (Submerged at Finished Grade, dw = 0.0 m): Terzaghi surcharge term drops to 272.20 kPa; q_ult = 1,007.54 kPa; Q_all = 1,343.39 kN. This represents a 22.9% drop relative to dry ground (and over 50% drop in purely granular soils).

Table 4: Step-by-Step Calculated Bearing Capacities Across Hydrological Cases
Subgrade Hydrology CaseFormulationCohesion Term (kPa)Surcharge Term (kPa)Soil Weight Term (kPa)Ultimate Capacity q_ult (kPa)Allowable Capacity q_all (kPa)Allowable Column Load Q_all (kN)
Dry Subgrade (dw >= 3.5 m)Terzaghi (1943)616.40480.82210.101,307.32435.771,743.08
Dry Subgrade (dw >= 3.5 m)Meyerhof (1963)751.65570.66289.041,611.35537.122,148.48
GWT at Footing Base (dw = 1.5 m)Terzaghi (1943)616.40480.82118.941,216.16405.391,621.56
GWT at Footing Base (dw = 1.5 m)Meyerhof (1963)751.65570.66163.791,486.10495.371,981.47
Submerged at Grade (dw = 0.0 m)Terzaghi (1943)616.40272.20118.941,007.54335.851,343.39
Submerged at Grade (dw = 0.0 m)Meyerhof (1963)751.65323.01163.791,238.45412.821,651.27

8. Common Engineering Pitfalls in Foundation Sizing

Geotechnical and foundation designers must avoid these critical errors:

• Overlooking Seasonal Water Table Fluctuations: Testing during dry seasons without accounting for high winter water tables can cause unexpected 20% to 50% capacity drops.

• Double-Counting Embedment: Relying on Meyerhof’s high depth factors where future excavations, utility trenches, or grading will remove the perimeter surcharge.

• Confusing Gross vs. Net Bearing Capacity: Supplying gross allowable capacity without clarifying that footing concrete and backfill weight must be subtracted to obtain allowable net soil pressure.

• Ignoring Deep Soft Strata: Neglecting soft compressible clay layers located within the stress bulb (1.5B to 2.0B beneath the footing base).

Frequently Asked Questions

Meyerhof is preferred when footings are moderately embedded (Df/B > 0.5) to capture real overburden shearing resistance, when loads have horizontal or moment inclination components (requiring inclination factors), or when designing deep piers and caissons.

Standard Citations & Technical References

  • Theoretical Soil Mechanics
    John Wiley & Sons

    Seminal 1943 treatise by Karl Terzaghi establishing the classical bearing capacity theory.

  • Some Recent Research on the Bearing Capacity of Foundations
    Canadian Geotechnical Journal

    G.G. Meyerhof’s foundational 1963 paper introducing shape, depth, and inclination factors in the Canadian Geotechnical Journal.

  • Principles of Foundation Engineering (9th Edition)
    Cengage Learning

    Comprehensive textbook by B.M. Das and N. Sivakugan detailing modern shallow foundation design.

  • Foundation Analysis and Design (5th Edition)
    McGraw-Hill Education

    Classic authoritative reference manual by Joseph E. Bowles.

NI

Md. Nur Islam

Founder of EngiVanta

Founder of EngiVanta. Directing platform architecture, numerical calculation standards, and engineering publications across civil and mechanical domains.