Shaft Design for Combined Torsion, Bending, and Fatigue: ASME B106.1M & Goodman Criteria
Power transmission shafts experience combined cyclic reversed bending, steady torsion, and stress concentrations. This guide details Marin endurance limit modifications, DE-Goodman, ASME Elliptic, and Soderberg failure criteria, keyway notch factors, and a complete 45 kW electric drive shaft benchmark.
Transmission shafts are the mechanical backbone of rotary machinery, transmitting power between motors, gearboxes, belt pulleys, and fluid impellers. In virtually every real-world application, a rotating shaft is subjected to simultaneous fluctuating multiaxial stresses: reversed bending stress from transverse belt or gear loads, and steady torsional shear stress from transmitted power.
As the shaft rotates, any surface fiber transitions cyclically from peak tension to peak compression every revolution (fully reversed fatigue, R = -1). Meanwhile, transmitted torque generates steady shear stress.
Historical elastic failures and fatigue disasters led to the development of standardized fatigue sizing protocols. The ASME Standard B106.1M (Design of Transmission Shafting) and the Distortion Energy (DE) Goodman and ASME Elliptic formulations provide closed-form equations that directly determine the minimum required shaft diameter to prevent both high-cycle fatigue failure and static yield during transient shock overloads.
This guide presents the multiaxial fatigue formulation, Marin endurance modifications, keyway stress concentration factors, and a worked benchmark for a 45 kW motor drive shaft.
1. Multiaxial Stress State in a Rotating Shaft
For a solid circular shaft of diameter d subjected to alternating bending moment Ma, mean bending moment Mm, alternating torque Ta, and mean torque Tm:
Von Mises Equivalent Alternating and Mean Stresses
For a shaft rotating at constant speed under steady transverse loads, bending is purely reversed (Mm = 0) and steady torque has zero alternating component (Ta = 0). Applying Distortion Energy theory yields:
2. Marin Endurance Limit Modification (Se)
The endurance limit of the actual shaft component (Se) is derived from the ideal polished rotating-beam laboratory specimen limit (Se' = 0.5 · Sut for steel ≤ 1400 MPa) using the Marin formulation:
| Marin Factor | Symbol | Engineering Formulation / Baseline Values | Benchmark Value |
|---|---|---|---|
| Surface Condition | ka | ka = a · Sut^b (For cold-drawn steel: a = 4.51, b = -0.265 in MPa) | 0.822 |
| Size Factor | kb | kb = 1.24 · d^(-0.107) for 2.79 mm ≤ d ≤ 51 mm | 0.825 |
| Load Factor | kc | kc = 1.00 for bending (Distortion Energy handles shear conversion) | 1.000 |
| Temperature Factor | kd | kd = 1.00 for operating temperature T ≤ 450°C | 1.000 |
| Reliability Factor | ke | ke = 0.814 for 99% reliability (0.897 for 90%, 0.753 for 99.9%) | 0.814 |
3. Closed-Form Shaft Diameter Sizing Equations
Setting the operating stress state on the fatigue failure boundary with design safety factor n yields direct closed-form solutions for minimum shaft diameter d:
DE-Goodman Criterion (Standard Industrial Baseline)
The DE-Goodman criterion uses ultimate tensile strength (Sut) on the mean stress axis:
DE-ASME Elliptic Criterion (Basis of ASME B106.1M)
The ASME Elliptic criterion connects Se on the alternating axis with yield strength Sy on the mean axis using an elliptical quadrant, preventing over-conservative shaft sizing:
4. Stress Concentration Factors (Kf, Kfs) at Shaft Features
Local geometry changes amplify nominal stress via fatigue notch sensitivity q: Kf = 1 + q·(Kt - 1).
| Shaft Feature / Discontinuity | Bending Factor Kf | Torsion Factor Kfs | Design Note |
|---|---|---|---|
| Profile End-Mill Keyway | 2.0 | 1.6 | Abrupt end corners; highest stress concentration |
| Sled-Runner Keyway | 1.6 | 1.3 | Gradual cutter runout; superior fatigue life |
| Shoulder Fillet — Sharp (r/d = 0.02) | 2.5 | 1.8 | Bearing seating with insufficient fillet radius |
| Shoulder Fillet — Well-rounded (r/d = 0.10) | 1.5 | 1.2 | Optimized transition fillet |
| Retaining Ring (Snap-Ring) Groove | 3.0 | 2.4 | Severe notch; keep away from high-bending locations |
5. Worked Industrial Benchmark: 45 kW Fan Drive Shaft
A solid steel drive shaft transmits power from an electric motor to an industrial ventilation fan:
• Power: P = 45.0 kW (60.3 hp) at N = 1200 rpm (ω = 125.66 rad/s) • Reversed Bending Moment: Ma = 520.0 N·m (Mm = 0) • Material: AISI 1045 Cold-Drawn Carbon Steel (Sut = 630 MPa, Sy = 530 MPa, Se' = 315 MPa) • Geometry: Profile end-mill keyway (Kf = 2.0, Kfs = 1.6) • Target: 99% reliability (ke = 0.814), safety factor n = 2.0
Steel Weight & Bar Stock Calculator
Determine round bar shaft mass, cross-sectional area, and volume.
Mechanical Engineering Toolbox (ME Toolbox)
Run shaft torsional shear, combined stress, and beam deflection calculations.
Step 1: Steady Torque & Modified Endurance Limit
• Steady Mean Torque: Tm = P / ω = 45,000 / 125.6637 = 358.10 N·m (Ta = 0) • Modified Endurance Limit: Se = 0.822 · 0.825 · 1.0 · 1.0 · 0.814 · 315.0 MPa = 174.05 MPa (1.7405 × 10⁸ Pa)
Step 2: Shaft Diameter per DE-Goodman and ASME Elliptic
• Alternating Bending Term: (2 · Kf · Ma) / Se = (2 · 2.0 · 520.0) / (1.7405 × 10⁸) = 1.1951 × 10⁻⁵ m³ • Goodman Torsional Term: (√3 · Kfs · Tm) / Sut = (1.732 · 1.6 · 358.10) / (6.30 × 10⁸) = 1.5753 × 10⁻⁶ m³ • Sum of Terms: 1.1951 × 10⁻⁵ + 1.5753 × 10⁻⁶ = 1.3526 × 10⁻⁵ m³ • DE-Goodman Diameter: d = [ (32 / π) · 1.3526 × 10⁻⁵ ]^(1/3) = (1.3777 × 10⁻⁴)^(1/3) = 0.05165 m = 51.65 mm • ASME Elliptic Diameter: d = { (32 / π) · √[ (1.1951 × 10⁻⁵)² + (1.8725 × 10⁻⁶)² ] }^(1/3) = 0.04976 m = 49.76 mm
Step 3: Specification Selection & Static Yield Check
• Standard Metric Bearing Bore: Specify d = 55.0 mm (Matches standard 6211 deep-groove ball bearing bore per ISO 15 boundary dimensions). • Actual Fatigue Safety Factor: n = 2.41 at d = 55.0 mm. • Static Yield Safety Factor under 150% peak startup shock: σvM = 104.2 MPa << Sy = 530 MPa (Static safety factor > 5.0).
Frequently Asked Questions
In a shaft transmitting constant power under steady belt or gear radial loads, the bending moment plane remains fixed in space while the shaft rotates. Each outer fiber therefore cycles from peak tension to peak compression on every revolution (fully reversed fatigue, R = -1), whereas steady transmitted torque creates constant mean shear stress.
Standard Citations & Technical References
- ASME B106.1M: Design of Transmission ShaftingAmerican Society of Mechanical Engineers (ASME)
American National Standard for shaft sizing under combined loading.
- Peterson's Stress Concentration Factors (3rd Edition)John Wiley & Sons / Walter D. Pilkey
Comprehensive charts and equations for shoulder fillets, keyways, and grooves.
- Shigley's Mechanical Engineering Design (11th Edition)McGraw-Hill Education
Chapter 7: Shafts and Shaft Components.
Md. Nur Islam
Founder of EngiVantaFounder of EngiVanta. Directing platform architecture, numerical calculation standards, and engineering publications across civil and mechanical domains.